Geotechnical Consortium (1984): (Table 4) Summary of consolidation and permeability at DSDP Hole 75-532A [dataset]. PANGAEA, https://doi.org/10.1594/PANGAEA.810284, In supplement to: Geotechnical Consortium (1984): Geotechnical properties of sediments from Walvis Ridge, Deep Sea Drilling Project, Leg 75, Hole 532A. In: Hay, WW; Sibuet, J-C; et al. (eds.), Initial Reports of the Deep Sea Drilling Project (U.S. Govt. Printing Office), 75, 1109-1127, https://doi.org/10.2973/dsdp.proc.75.141.1984
Always quote citation above when using data! You can download the citation in several formats below.
Project(s):
Deep Sea Drilling Project (DSDP)
Coverage:
Latitude: -19.744000 * Longitude: 10.518800
Date/Time Start: 1980-08-20T00:00:00 * Date/Time End: 1980-08-20T00:00:00
Minimum DEPTH, sediment/rock: 1.25 m * Maximum DEPTH, sediment/rock: 198.35 m
Event(s):
75-532A * Latitude: -19.744000 * Longitude: 10.518800 * Date/Time: 1980-08-20T00:00:00 * Elevation: -1331.0 m * Penetration: 199.6 m * Recovery: 161 m * Location: South Atlantic Ocean * Campaign: Leg75 * Basis: Glomar Challenger * Method/Device: Drilling/drill rig (DRILL) * Comment: 42 cores; 182.6 m cored; 17 m drilled; 88.2 % recovery
Parameter(s):
# | Name | Short Name | Unit | Principal Investigator | Method/Device | Comment |
---|---|---|---|---|---|---|
1 | Sample code/label | Sample label | Geotechnical Consortium | DSDP/ODP/IODP sample designation | ||
2 | DEPTH, sediment/rock | Depth sed | m | Geocode – mbsf | ||
3 | Identification | ID | Geotechnical Consortium | TAMU = Texas A&M University; CU = University of Colorado; URI = University of Rhode Island; SDSU = San Diego State University | ||
4 | Void ratio | Void ratio | Geotechnical Consortium | At effective overburden pressure | ||
5 | Effective overburden pressure | Overb press ef | kPa | Geotechnical Consortium | Vertical | |
6 | Comment | Comment | Geotechnical Consortium | |||
7 | Permeability | Permeab | cm/s | Geotechnical Consortium | see reference(s) | At effective overburden pressures measured by falling head test |
8 | Void ratio | Void ratio | Geotechnical Consortium | At preconsolidation pressure | ||
9 | Preconsolidation pressure | Pc | kPa | Geotechnical Consortium | see reference(s) | |
10 | Permeability | Permeab | cm/s | Geotechnical Consortium | Calculated, see reference(s) | At preconsolidation pressure, computed from the results of consolidation test |
11 | Permeability | Permeab | cm/s | Geotechnical Consortium | see reference(s) | At preconsolidation pressure, measured by falling head test |
12 | Compression index | Cc | Geotechnical Consortium | Calculated, see reference(s) | ||
13 | Overconsolidation ratio | Pc/Po | Geotechnical Consortium | Calculated, see reference(s) |
License:
Creative Commons Attribution 3.0 Unported (CC-BY-3.0)
Size:
552 data points
Data
1 Sample label (DSDP/ODP/IODP sample designation) | 2 Depth sed [m] (mbsf) | 3 ID (TAMU = Texas A&M University; ...) | 4 Void ratio (At effective overburden pressure) | 5 Overb press ef [kPa] (Vertical) | 6 Comment | 7 Permeab [cm/s] (At effective overburden press...) | 8 Void ratio (At preconsolidation pressure) | 9 Pc [kPa] (see reference(s)) | 10 Permeab [cm/s] (At preconsolidation pressure,...) | 11 Permeab [cm/s] (At preconsolidation pressure,...) | 12 Cc (Calculated, see reference(s)) | 13 Pc/Po (Calculated, see reference(s)) |
---|---|---|---|---|---|---|---|---|---|---|---|---|
75-532A-1-1 | 1.25 | Test group TAMU | 5.33 | 4.5 | 6.45E-6 | 0.00 | 35 | 341E-9 | 3.0E-6 | 0.63 | 7.36 | |
75-532A-2-1 | 3.30 | Test group CU | 2.51 | 11.6 | Constant rate of deformation (CRD) test | 595E-9 | 2.25 | 50 | 365E-9 | 0.42 | 1.30 | |
75-532A-2-3 | 6.90 | Test group TAMU | 2.57 | 26.1 | 775E-9 | 2.56 | 28 | 692E-9 | 760E-9 | 0.78 | 1.07 | |
75-532A-3-1 | 8.75 | Test group TAMU | 2.34 | 34.7 | 244E-9 | 2.73 | 10 | 332E-9 | 591E-9 | 0.74 | 3.29 | |
75-532A-3-3 | 11.75 | Test group TAMU | 2.28 | 47.0 | 970E-9 | 2.25 | 84 | 384E-9 | 900E-9 | 0.66 | 1.79 | |
75-532A-4-2 | 14.45 | Test group TAMU | 2.16 | 58.0 | 26.2E-6 | 2.11 | 75 | 590E-9 | 22.9E-6 | 0.65 | 1.29 | |
75-532A-4-3 | 16.30 | Test group CU | 3.16 | 67.0 | Constant rate of deformation (CRD) test | 510E-9 | 3.03 | 365E-9 | 0.76 | 1.86 | ||
75-532A-5-2 | 19.40 | Test group TAMU | 2.42 | 80.7 | 465E-9 | 2.34 | 150 | 230E-3 | 365E-9 | 0.99 | 1.86 | |
75-532A-6-2 | 23.40 | Test group TAMU | 2.29 | 96.6 | 1.41E-6 | 2.23 | 160 | 532E-9 | 1.24E-6 | 0.75 | 1.66 | |
75-532A-7-1 | 26.60 | Test group TAMU | 3.43 | 108.4 | 5.2E-6 | 3.37 | 125 | 425E-9 | 4.6E-6 | 1.55 | 1.15 | |
75-532A-9-1 | 34.45 | Test group TAMU | 2.58 | 138.9 | 295E-9 | 2.55 | 170 | 215E-9 | 270E-9 | 1.04 | 1.22 | |
75-532A-9-1 | 34.56 | Test group URI | 2.68 | 140.3 | 331E-9 | 2.28 | 190 | 298E-9 | 1.22 | 1.35 | ||
75-532A-9-2 | 36.30 | Test group TAMU | 2.18 | 147.0 | 196E-9 | 2.32 | 120 | 92E-9 | 274E-9 | 0.87 | 0.81 | |
75-532A-10-3 | 41.75 | Test group CU | 2.20 | 172.0 | Constant rate of deformation (CRD) test | 101E-9 | 2.32 | 115 | 121E-9 | 0.89 | 0.67 | |
75-532A-10-3 | 42.00 | Test group SDSU | 2.28 | 177.0 | 300E-9 | 2.35 | 185 | 1.10 | 1.04 | |||
75-532A-11-2 | 44.75 | Test group TAMU | 2.25 | 185.0 | 478E-9 | 2.20 | 255 | 264E-9 | 422E-9 | 0.93 | 1.38 | |
75-532A-12-1 | 48.20 | Test group TAMU | 2.08 | 200.1 | 223E-9 | 2.42 | 87 | 133E-9 | 395E-9 | 0.81 | 0.43 | |
75-532A-12-2 | 50.10 | Test group TAMU | 2.45 | 207.3 | 801E-9 | 2.56 | 180 | 457E-9 | 1.04E-6 | 1.00 | 0.87 | |
75-532A-14-1 | 57.10 | Test group CU | 2.44 | 233.0 | Constant rate of deformation (CRD) test | 423E-9 | 2.57 | 160 | 610E-9 | 1.24 | 0.69 | |
75-532A-15-2 | 62.30 | Test group CU | 2.19 | 253.0 | Constant rate of deformation (CRD) test | 150E-9 | 2.10 | 345 | 125E-9 | 1.20 | 1.36 | |
75-532A-16-2 | 66.70 | Test group TAMU | 2.26 | 270.6 | 366E-9 | 2.25 | 290 | 382E-9 | 365E-9 | 1.12 | 1.07 | |
75-532A-17-2 | 71.00 | Test group SDSU | 2.79 | 268.0 | 15E-9 | 2.27 | 291 | 1.40 | 1.08 | |||
75-532A-17-2 | 71.30 | Test group TAMU | 2.35 | 288.1 | 188E-9 | 2.32 | 330 | 102E-9 | 184E-9 | 1.17 | 1.15 | |
75-532A-18-2 | 75.55 | Test group CU | 1.90 | 303.0 | Constant rate of deformation (CRD) test | 135E-9 | 1.80 | 405 | 115E-9 | 1.15 | 1.34 | |
75-532A-19-1 | 79.41 | Test group URI | 2.70 | 317.0 | 4.83E-6 | 2.20 | 320 | 176E-9 | 125E-9 | 0.95 | 1.01 | |
75-532A-19-2 | 80.55 | Test group TAMU | 2.68 | 320.9 | 172E-9 | 2.88 | 250 | 39.2E-9 | 270E-9 | 1.46 | 0.78 | |
75-532A-19-2 | 81.00 | Test group SDSU | 2.71 | 323.0 | 70E-9 | 1.99 | 337 | 1.00 | 1.04 | |||
75-532A-20-2 | 85.20 | Test group CU | 2.96 | 336.0 | Constant rate of deformation (CRD) test | 597E-9 | 3.00 | 290 | 635E-9 | 1.28 | 0.86 | |
75-532A-21-2 | 89.85 | Test group TAMU | 2.08 | 354.7 | 98E-9 | 2.18 | 370 | 98.3E-9 | 126E-9 | 1.13 | 1.04 | |
75-532A-22-2 | 93.80 | Test group CU | 2.35 | 371.0 | Constant rate of deformation (CRD) test | 300E-9 | 2.33 | 390 | 295E-9 | 1.24 | 1.05 | |
75-532A-23-1 | 96.90 | Test group TAMU | 2.18 | 382.1 | 940E-9 | 2.05 | 495 | 270E-9 | 738E-9 | 0.87 | 1.30 | |
75-532A-24-2 | 102.95 | Test group TAMU | 2.28 | 411.9 | 411E-9 | 2.46 | 320 | 157E-9 | 598E-9 | 1.07 | 0.78 | |
75-532A-25-2 | 107.10 | Test group CU | 1.76 | 430.0 | Constant rate of deformation (CRD) test | 135E-9 | 1.73 | 470 | 190E-9 | 0.91 | 1.09 | |
75-532A-26-2 | 111.30 | Test group TAMU | 2.26 | 448.2 | 580E-9 | 2.38 | 390 | 234E-9 | 755E-9 | 0.63 | 0.87 | |
75-532A-28-2 | 119.60 | Test group CU | 1.54 | 486.0 | Constant rate of deformation (CRD) test | 77E-9 | 1.52 | 530 | 73E-9 | 1.03 | 1.09 | |
75-532A-29-2 | 124.75 | Test group CU | 2.08 | 508.0 | 230E-9 | 2.11 | 469 | 245E-9 | 1.08 | 0.91 | ||
75-532A-30-1 | 128.00 | Test group TAMU | 1.87 | 523.5 | 23.9E-9 | 1.84 | 690 | 28.8E-9 | 21.9E-9 | 1.14 | 1.32 | |
75-532A-31-1 | 132.10 | Test group CU | 1.41 | 544.0 | Constant rate of deformation (CRD) test | 61E-9 | 1.38 | 640 | 56E-9 | 0.72 | 1.18 | |
75-532A-32-2 | 139.50 | Test group CU | 1.23 | 566.0 | Constant rate of deformation (CRD) test | 55E-9 | 1.18 | 720 | 47E-9 | 0.65 | 1.27 | |
75-532A-33-2 | 142.10 | Test group CU | 1.37 | 609.0 | Constant rate of deformation (CRD) test | 41.5E-9 | 1.38 | 590 | 43E-9 | 0.71 | 0.97 | |
75-532A-34-1 | 145.20 | Test group TAMU | 1.46 | 618.9 | 55.5E-9 | 1.45 | 650 | 42.9E-9 | 54.1E-9 | 0.57 | 0.05 | |
75-532A-34-3 | 147.50 | Test group CU | 1.26 | 636.0 | Constant rate of deformation (CRD) test | 50E-9 | 1.23 | 760 | 46E-9 | 0.76 | 0.19 | |
75-532A-35-3 | 151.80 | Test group CU | 1.21 | 663.0 | Constant rate of deformation (CRD) test | 53E-9 | 1.23 | 510 | 57E-9 | 0.56 | 0.77 | |
75-532A-36-2 | 155.10 | Test group TAMU | 1.31 | 677.1 | 41.2E-9 | 1.31 | 680 | 14.9E-9 | 41.2E-9 | 0.67 | 1.01 | |
75-532A-38-1 | 162.00 | Test group TAMU | 1.26 | 721.6 | 2.0E-6 | 1.56 | 200 | 21E-9 | 4.45E-6 | 0.59 | 0.28 | |
75-532A-40-2 | 170.05 | Test group TAMU | 1.24 | 771.8 | 17.3E-9 | 1.50 | 310 | 12.3E-9 | 51E-9 | 0.58 | 0.40 | |
75-532A-41-1 | 173.60 | Test group CU | 1.35 | 791.0 | Constant rate of deformation (CRD) test | 45E-9 | 1.32 | 890 | 42E-9 | 0.92 | 1.13 | |
75-532A-42-3 | 180.00 | Test group CU | 1.17 | 829.0 | Constant rate of deformation (CRD) test | 34E-9 | 1.20 | 710 | 38E-9 | 0.55 | 0.86 | |
75-532A-44-1 | 186.45 | Test group TAMU | 1.24 | 859.7 | 77.9E-9 | 1.36 | 460 | 60.7E-9 | 191E-9 | 0.46 | 0.54 | |
75-532A-47-2 | 197.40 | Test group TAMU | 0.99 | 944.2 | 44.5E-9 | 0.97 | 1100 | 25.5E-9 | 39.5E-9 | 0.65 | 1.17 | |
75-532A-47-3 | 198.35 | Test group CU | 1.10 | 949.0 | Constant rate of deformation (CRD) test | 29.5E-9 | 1.12 | 860 | 30.4E-9 | 0.52 | 0.91 |