Roller, Sybille; Pohl, C; Behrmann, Jan-Hinrich (2003): (Table 1) Petrological description and consolidation properties of ODP Site 186-1150 and Hole 186-1151A [dataset]. PANGAEA, https://doi.org/10.1594/PANGAEA.783903, Supplement to: Roller, S et al. (2003): Data report: Triaxial shear strength of sediments and sedimentary rocks from the Japan Trench, ODP Leg 186. In: Suyehiro, K; Sacks, IS; Acton, GD; Oda, M (eds.) Proceedings of the Ocean Drilling Program, Scientific Results, College Station, TX (Ocean Drilling Program), 186, 1-19, https://doi.org/10.2973/odp.proc.sr.186.115.2003
Always quote citation above when using data! You can download the citation in several formats below.
Abstract:
In order to determine the shear parameters of the forearc sedimentary strata drilled during Ocean Drilling Program Leg 186, West Pacific Seismic Network, Japan Trench, eight whole-round samples were selected from different depths in the drilled sections of Sites 1150 and 1151. Whereas Site 1150 lays above the seismically active part of the subduction zone, Site 1151 is situated in an aseismic zone. The aim of the triaxial tests was, apart from determination of the static stress strain behavior of the sediments, to test the hypothesis that the static stress strain parameter could differ for each sites. In order to simulate undrained deformation conditions according to the high clay mineral content of the strata, consolidated undrained shear tests were performed in a triaxial testing setup. Measurements of water content, grain density, organic content, and microtextural investigations under the scanning electron microscope (SEM) accompanied the compression experiments. After the saturation and consolidation stages were completed, failure occurred in the compression stage of the experiments at peak strengths of 280-7278 kPa. The stiffness moduli calculated for each sample from differential stress vs. strain curves show a linear relationship with depth and range between 181 and 5827 kPa. Under the SEM, the artificial fault planes of the tested specimen only show partial alignment of clay minerals because of the high content of microfossils.
Project(s):
Ocean Drilling Program (ODP)
Coverage:
Median Latitude: 39.038597 * Median Longitude: 143.332920 * South-bound Latitude: 38.751980 * West-bound Longitude: 143.331910 * North-bound Latitude: 39.181910 * East-bound Longitude: 143.334400
Date/Time Start: 1999-06-22T18:30:00 * Date/Time End: 1999-08-02T17:45:00
Minimum DEPTH, sediment/rock: 63 m * Maximum DEPTH, sediment/rock: 1101 m
Event(s):
186-1150A * Latitude: 39.181910 * Longitude: 143.331910 * Date/Time Start: 1999-06-22T18:30:00 * Date/Time End: 1999-06-26T22:15:00 * Elevation: -2680.8 m * Penetration: 722.6 m * Recovery: 566.4 m * Location: North Pacific Ocean * Campaign: Leg186 * Basis: Joides Resolution * Method/Device: Drilling/drill rig (DRILL) * Comment: 76 cores; 722.6 m cored; 0 m drilled; 78.4 % recovery
186-1150B * Latitude: 39.181900 * Longitude: 143.332450 * Date/Time Start: 1999-06-26T22:15:00 * Date/Time End: 1999-07-03T13:30:00 * Elevation: -2680.8 m * Penetration: 1181.6 m * Recovery: 269.29 m * Location: North Pacific Ocean * Campaign: Leg186 * Basis: Joides Resolution * Method/Device: Drilling/drill rig (DRILL) * Comment: 50 cores; 478.3 m cored; 703.3 m drilled; 56.3 % recovery
186-1151A * Latitude: 38.751980 * Longitude: 143.334400 * Date/Time Start: 1999-07-28T22:00:00 * Date/Time End: 1999-08-02T17:45:00 * Elevation: -2182.2 m * Penetration: 1113.6 m * Recovery: 707.6 m * Location: North Pacific Ocean * Campaign: Leg186 * Basis: Joides Resolution * Method/Device: Drilling/drill rig (DRILL) * Comment: 108 cores; 1035.6 m cored; 0 m drilled; 68.3 % recovery
Parameter(s):
# | Name | Short Name | Unit | Principal Investigator | Method/Device | Comment |
---|---|---|---|---|---|---|
1 | Event label | Event | ||||
2 | Sample code/label | Sample label | Roller, Sybille | DSDP/ODP/IODP sample designation | ||
3 | DEPTH, sediment/rock | Depth sed | m | Geocode – mbsf | ||
4 | Lithology/composition/facies | Lithology | Roller, Sybille | |||
5 | Induration | Induration | Roller, Sybille | |||
6 | Sample ID | Sample ID | Roller, Sybille | |||
7 | Method comment | Method comm | Roller, Sybille | CU = consolidated undrained, CD = consolidated drained | ||
8 | Height | h | mm | Roller, Sybille | ||
9 | Diameter | Ø | mm | Roller, Sybille | ||
10 | Density, grain | Density grain | g/cm3 | Roller, Sybille | Scanning electron microscope (SEM) | |
11 | Water content, wet mass | Water wm | % | Roller, Sybille | Scanning electron microscope (SEM) | |
12 | Organic matter | OM | % | Roller, Sybille | Calculated from weight loss after ignition at 550 °C | |
13 | Pressure, porewater excess | Press porewater xs | kPa | Roller, Sybille | saturation pressure | |
14 | Consolidation stress | Consol stress | kPa | Roller, Sybille | ||
15 | Deformation, rate | Def rate | mm/min | Roller, Sybille | ||
16 | Pressure, difference | dP | kPa | Roller, Sybille | yield strength maximum (vertical stress (sigma 1) - horzontal stress (sigma 3) | |
17 | Stiffness modulus | Stiff mod | kPa | Roller, Sybille |
License:
Creative Commons Attribution 3.0 Unported (CC-BY-3.0)
Size:
185 data points